Product Discription

LSS Oil Fired Steam Generator

The LSS Oil Vertical Vapour Generator receives the vertical pipe structure. There are two lower rings and a special cylinder for the cartridge between the top and bottom housing pipes, which make up three combustion gases. to swell and burn.

For water heaters and condensers, the thermal efficiency can reach 93% and 100%. With steam -water separators and external steam -water separators, it can provide high -quality dry steam, save fuel, reduce the system scale and extend service life.

1. Easy Maintenance:

Inspection doors are set at the bottom to check and clean the furnace interior for easy maintenance.

2. in line with environmental protection:

high quality and reliable burner, so that fuel can be fully burned, while greatly reducing harmful emissions in flue gas. The test results of relevant departments show that the fuel (gas) steam generator meets the national environmental protection requirements.

3. The amount of evaporation can be increased.:

Steam generators can be modularized into several units (unlimited number) and controlled by computer.Total evaporation can be added freely.The relevant components of steam generator (including water treatment, water pump, burner, electronic control box and main valve instruments) are already in the factory.

4. Installation is an integral whole:

It can be connected with water, electricity and steam pipes on site, which saves time and effort in installation.

5. Reliable accessories:

matching burners, control boxes, water treatment, and valves, pumps are made of domestic high-quality equipment. The matching equipment can ensure the safe and reliable operation of the steam generator and improve the overall quality of the steam generator.

Technical Parameters

Main Technical Reference for Fuel (Gas) Steam Generator
Item Unit			LSS0.05	LSS0.1	LSS0.15	LSS0J2
Rated evaporation		Kg/h	50	100	150	200
Rated Pressure PTEPREppoPressure		MPa	0.4/0.7
Rated steam temperature		c	151/171
Rated feed water temperature		°C	20
Evaporator efficiency		/	>92%
Applicable Fuel		/	Gas light oil
Theoretical fuel consumption	Gas	NM3/h	4	8	12	16
	Light Oil	Kg/h	3.3	6.5	9.8	13
Gas supply pressure		mbar	60- 100
water volume		L	<30

Note: The fuel consumption in the table is based on the low calorific value of biomass particles 17084 KJ/Kg (4085 Kcal/Kg).Calculations show that if the low calorific value of biomass fuel is higher than that, the corresponding fuel consumption will be more economical than the values in the table.

Configuration and Interface Size of Fuel (Gas) Steam Generator
Item Unit			LSS0.05	LSSO.l	LSS0.15	LSS0.2
Outward Size of Main Engine (length * width * height)	/	mm	620*620*830	690*690*968	750*750*1130	800*800*1286
Transport Dimension	/	mm	206	252	303	350
Mainframe Transport Weight	DN	mm	G 1/2-	Gl'	Gl"	G 1*
Main Steam Valve Pipe Diameter	DN	mm	Gl/2"	Gl/2-	Gl/2-	Gl/2°
Feed Water Valve	DN	mm	G1 1/4”	G11/4-	G11/4-	G11/4-
Safety Valve Diameter	DN	mm	Gf	GF	Gl"	Gl"
Drain Valve Pipe Diameter	DN	mm	133	133	159	159

Remarks: We will reserve rights to change the above mentioned data due to continuous policy transformation and product improvement.

     It is one of the ten most famous towns in Zhongzhou, which is adjacent to National Highway 107 in the South and Beijing-Guangzhou Railway in the north. The company has the B-class boiler manufacturing license issued by the General Administration of Inspection and Quarantine of the State Quality Supervision Bureau and the D1 and D2-class pressure vessel manufacturing license. It is a comprehensive manufacturer of steam boilers, hot water boilers, heat carrier boilers, pressure vessels of Class I and II and auxiliary machines for various boilers. The company was founded in 1987.

     After relocation and expansion, it now has perfect production equipment and testing means, a high-quality staff and technical team, and has established and improved a set of quality assurance system. The quality policy of "quality-oriented, safety first, energy-saving, environmental protection, refinement" and "the pass rate of main parts inspection is over 95%, the pass rate of welding seam inspection is over 98%, the pass rate of product inspection is 100%, the pass rate of products manufactured is 100%, and the implementation rate of regulations and standards is 100%" have been formulated.

Product quality is safe and reliable, environmental protection and energy saving, and conforms to the national standards and industry standards. Pressure vessel products are inspected by the quality and technical supervision department and issued with product inspection certificate. 

Xinxiang Xinguo Container Manufacturing Co., Ltd. is willing to cooperate sincerely with friends from all walks of life to create brilliance!